Quantcast
Channel: Mellanox Interconnect Community: Message List
Viewing all 6275 articles
Browse latest View live

Re: What is the recommended firmware updating tool for Mellanox HCAs and/or NICs?


-E- Failed to set configuration: failed to set SRIOV params: Message receipt ack

$
0
0

Hello,

I want to use SR-IOV function.

so I configure it as the "HowTo Configure SR-IOV for ConnectX-3 with KVM (InfiniBand) " instructed.

But when I run the command " mlxconfig -d /dev/mst/mt4099_pciconf0 set SRIOV_EN=1 NUM_OF_VFS=4". There is some error happened and I can't find any information about it.

Here is the output:

Device #1:

----------

Device type:    ConnectX3      

PCI device:     /dev/mst/mt4099_pciconf0

Configurations:                              Current         New

         SRIOV_EN                            False(0)        True(1)        

         NUM_OF_VFS                          8               4              

Apply new Configuration? ? (y/n) [n] : y

Applying... Failed!

-E- Failed to set configuration: failed to set SRIOV params: Message receipt ack

 

I use 12 computers, at first there is two computers that could execute the command correctly. But there is ten computers output that the firmware is unsupported for the command

"mlxconfig -d /dev/mst/mt4099_pciconf0 q", so I update the firmware of all the computer as requested. After that, all the computer could execute the command  "mlxconfig -d /dev/mst/mt4099_pciconf0 q". But even the first two computers that could execute the command  " mlxconfig -d /dev/mst/mt4099_pciconf0 set SRIOV_EN=1 NUM_OF_VFS=4" well could no longer running the command any more. It's very strange. I guess something was changed by the firmware update. Any help would be appreciate!!

Re: Which ESXi driver to use for SRP/iSER over IB (not Eth!)?

$
0
0

Does the included ESXi 6.5 have RDMA support for the hypervisor back to storage? or is it just for a guest. I really am only using SRP at a HOST to Storage level, nothing inside of the vm is infiniband aware.

 

Mellanox, if you arent going to release SRP drivers again, would you consider releasing the source for the old ones and we will take it from here..

Re: MLNX OFED error for RHEL 7.3 RT

$
0
0

Probably I deleted tjis log but below is different log with for the same error:

 

Logs dir: /tmp/MLNX_OFED_LINUX-3.4-2.0.0.0-3.10.0-514.2.2.rt56.424.el7.x86_64/OFED.29661.logs

[32m

Below is the list of OFED packages that you have chosen

   

(some may have been added by the installer due to package dependencies):

[0m

ofed-scripts

mlnx-ofa_kernel

mlnx-ofa_kernel-modules

mlnx-ofa_kernel-devel

knem

kernel-mft

iser

srp

isert

mlnx-sdp

mlnx-rds

 

 

Build ofed-scripts 3.4 RPM

Running  rpmbuild --rebuild  --define '_topdir /tmp/MLNX_OFED_LINUX-3.4-2.0.0.0-3.10.0-514.2.2.rt56.424.el7.x86_64/mlnx_iso.29365/OFED_topdir' --define '_sourcedir %{_topdir}/SOURCES' --define '_specdir %{_topdir}/SPECS' --define '_srcrpmdir %{_topdir}/SRPMS' --define '_rpmdir %{_topdir}/RPMS'  --define 'dist %{nil}' --target x86_64 --define '_prefix /usr' --define '_exec_prefix /usr' --define '_sysconfdir /etc' --define '_usr /usr' /tmp/MLNX_OFED_LINUX-3.4-2.0.0.0-3.10.0-514.2.2.rt56.424.el7.x86_64/mlnx_iso.29365/MLNX_OFED_SRC-3.4-2.0.0.0/SRPMS/ofed-scripts-3.4-OFED.3.4.2.0.0.src.rpm

Build mlnx-ofa_kernel 3.4 RPM

Running rpmbuild --rebuild  --define '_topdir /tmp/MLNX_OFED_LINUX-3.4-2.0.0.0-3.10.0-514.2.2.rt56.424.el7.x86_64/mlnx_iso.29365/OFED_topdir' --define '_sourcedir %{_topdir}/SOURCES' --define '_specdir %{_topdir}/SPECS' --define '_srcrpmdir %{_topdir}/SRPMS' --define '_rpmdir %{_topdir}/RPMS'  --nodeps --define '_dist .rhel7u3' --define 'configure_options   --with-core-mod --with-user_mad-mod --with-user_access-mod --with-addr_trans-mod --with-mthca-mod --with-mlx4-mod --with-mlx4_en-mod --with-mlx4_vnic-mod --with-mlx5-mod --with-cxgb3-mod --with-cxgb4-mod --with-nes-mod --with-ehca-mod --with-qib-mod --with-ipoib-mod --with-ipath_inf-mod --with-amso1100-mod --with-ocrdma-mod --with-sdp-mod --with-srp-mod --with-rds-mod --with-iser-mod --with-e_ipoib-mod --with-9pnet_rdma-mod --with-9p-mod --with-cxgb3i-mod --with-cxgb4i-mod --with-isert-mod' --define 'KVERSION 3.10.0-514.2.2.rt56.424.el7.x86_64' --define 'K_SRC /lib/modules/3.10.0-514.2.2.rt56.424.el7.x86_64/build' --define '_prefix /usr' /tmp/MLNX_OFED_LINUX-3.4-2.0.0.0-3.10.0-514.2.2.rt56.424.el7.x86_64/mlnx_iso.29365/MLNX_OFED_SRC-3.4-2.0.0.0/SRPMS/mlnx-ofa_kernel-3.4-OFED.3.4.2.0.0.1.g30039f7.src.rpm

[31mFailed to build mlnx-ofa_kernel 3.4 RPM [0m

Collecting debug info...

[31mSee /tmp/MLNX_OFED_LINUX-3.4-2.0.0.0-3.10.0-514.2.2.rt56.424.el7.x86_64/OFED.29661.logs/mlnx-ofa_kernel-3.4.rpmbuild.log [0m

-E- Failed to set configuration: failed to set SRIOV params: Message receipt ack

$
0
0

Hello,

I want to use SR-IOV function.

so I configure it as the "HowTo Configure SR-IOV for ConnectX-3 with KVM (InfiniBand) " instructed.

But when I run the command " mlxconfig -d /dev/mst/mt4099_pciconf0 set SRIOV_EN=1 NUM_OF_VFS=4". There is some error happened and I can't find any information about it.

Here is the output:

Device #1:

----------

Device type:    ConnectX3     

PCI device:     /dev/mst/mt4099_pciconf0

Configurations:                              Current         New

         SRIOV_EN                            False(0)        True(1)       

         NUM_OF_VFS                          8               4             

Apply new Configuration? ? (y/n) [n] : y

Applying... Failed!

-E- Failed to set configuration: failed to set SRIOV params: Message receipt ack

 

I use 12 computers, at first there is two computers that could execute the command correctly. But there is ten computers output that the firmware is unsupported for the command

"mlxconfig -d /dev/mst/mt4099_pciconf0 q", so I update the firmware of all the computer as requested. After that, all the computer could execute the command  "mlxconfig -d /dev/mst/mt4099_pciconf0 q". But even the first two computers that could execute the command  " mlxconfig -d /dev/mst/mt4099_pciconf0 set SRIOV_EN=1 NUM_OF_VFS=4" well could no longer running the command any more. It's very strange. I guess something was changed by the firmware update. Any help would be appreciate!!

Re: What is the recommended firmware updating tool for Mellanox HCAs and/or NICs?

$
0
0

Thanks for your reply.  So, my own understanding is in-line with yours. 

 

Regards,

 

Chin

Re: MLNX OFED error for RHEL 7.3 RT

$
0
0

Hi Oskar,

We need the contents of /tmp/MLNX_OFED_LINUX-3.4-2.0.0.0-3.10.0-514.2.2.rt56.424.el7.x86_64/OFED.29661.logs/mlnx-ofa_kernel-3.4.rpmbuild.log

Thanks and regards,
~Martijn

Re: MLNX OFED error for RHEL 7.3 RT

$
0
0

Hi Oskar,

 

We need the contents of /tmp/MLNX_OFED_LINUX-3.4-2.0.0.0-3.10.0-514.2.2.rt56.424.el7.x86_64/OFED.29661.logs/mlnx-ofa_kernel-3.4.rpmbuild.log

 

Can you please share that log file.

 

Thanks and regards,

~Martijn


Re: MLNX OFED error for RHEL 7.3 RT

$
0
0

can you give me your email. File is too big to paste here.

DPDK testpmd can't access device

$
0
0

EAL: Detected 2 lcore(s)

EAL: Probing VFIO support...

EAL: PCI device 0000:06:00.0 on NUMA socket -1

EAL:   probe driver: 15b3:1015 net_mlx5

PMD: mlx5.c:428: mlx5_pci_probe(): cannot access device, is mlx5_ib loaded? [ Yes it is loaded ]

EAL: PCI device 0000:06:00.1 on NUMA socket -1

EAL:   probe driver: 15b3:1015 net_mlx5

PMD: mlx5.c:428: mlx5_pci_probe(): cannot access device, is mlx5_ib loaded?

EAL: No probed ethernet devices

PANIC in main():

Empty set of forwarding logical cores - check the core mask supplied in the command parameters

Re: Which ESXi driver to use for SRP/iSER over IB (not Eth!)?

$
0
0

Section 4.3 of this article suggests that in-box ESXi drivers are RDMA-aware,  which you can also conclude from the very fact one of the modules related to these drivers is called nlmx4(5)_rdma. That doesn't mean though that RDMA is actually going to be effectively used for host-to-storage access. For iSCSI, that would require implementing iSER layer, which the in-box driver clearly doesn't have (after all, it's explicitly called "Software iSCSI Adapter" and it's like 100 years old). And, if VMware NFS could utilise RDMA, I'm pretty sure they'd already told us about it.

So, someone has to do some work here, either Mellanox or VMware or both. But they're not eager to tell us anything, as you can clearly see from 1/2 year lack of response to this thread...

Re: CentOS 7 KVM-SR-IOV Performance?

$
0
0

The patches provided by RH from link http://people.redhat.com/~alwillia/bz1299846/is solving the issue.

I have downloaded and installed (yum install *.rpm) the 3 user space packages (qemu-img, qemu-kvm and qemu-kvm-common) on the hypervisor.

The performance could be enhanced by as much as 90% and 65% in the case of 1KB and 4KB message size respectively.

 

qemu-img-1.5.3-105.el7_2.1.bz1299846.0.x86_64.rpm

qemu-kvm-1.5.3-105.el7_2.1.bz1299846.0.x86_64.rpm

qemu-kvm-common-1.5.3-105.el7_2.1.bz1299846.0.x86_64.rpm

 

Performance Known Issues#783496: When using a VF over RH7.X KVM, low throughput is expected.

http://www.mellanox.com/related-docs/prod_software/Mellanox_OFED_Linux_Release_Notes_3_3-1_0_0_0.pdf

Native VLAN configuration for Mellanox switches

$
0
0

I know the default native vlan on hybrid port is VLAN 1.

Do we have a command to configure/change this default native vlan on Mellanox switch?

Re: Native VLAN configuration for Mellanox switches

$
0
0

No.

You need to create new VLAN, and assign it to the relevant ports.

 

Ophir.

Re: -E- Failed to set configuration: failed to set SRIOV params: Message receipt ack


Re: HCA extended port counters

Re: DPDK testpmd can't access device

$
0
0

Hi Kaijun,

 

Did you bind the devices to UIO/VFIO? If so, you should bind it back to kernel driver. Mellanox PMD doesn't use UIO/VFIO but its control path goes through regular kernel driver unlike Intel NICs.

 

Thanks,

Yongseok

mlx4_0 Initializing and... nothing, fails? on Centos on Dell servers, MT25408

$
0
0

hi all,

 

I've a a very basic setup, directly two boxes via two MHEH28-XTC and I cannot activate them.

One peculiar thing is I get (randomly & !often):

 

[85947.090496] AMD-Vi: Event logged [

[85947.090539] IO_PAGE_FAULT device=09:00.7 domain=0x0000 address=0x00000000f6ffb000 flags=0x0050]

[85947.298509] AMD-Vi: Event logged [

[85947.298550] IO_PAGE_FAULT device=09:00.7 domain=0x0000 address=0x00000000f6ffb000 flags=0x0050]

 

which is the card itself, judging by the device id

Would you have and share some thoughts please?

 

$ ./flint/mstflint -d 09:00.0 q # for both cards

 

-W- Running quick query - Skipping full image integrity checks.

 

Image type:      FS2

FW Version:      2.9.1000

Device ID:       25408

Description:     Node             Port1            Port2 Sys image

GUIDs:           0008f104039a62a0 0008f104039a62a1 0008f104039a62a2 0008f104039a62a3

MACs:                                 000000000000     000000000001

VSD:

PSID:            MT_04A0110001

 

$ ibstat

CA 'mlx4_0'

    CA type: MT25408

    Number of ports: 2

    Firmware version: 2.9.1000

    Hardware version: a0

    Node GUID: 0x0008f104039a08dc

    System image GUID: 0x0008f104039a08df

    Port 1:

        State: Initializing

        Physical state: LinkUp

        Rate: 10

        Base lid: 1

        LMC: 0

        SM lid: 1

        Capability mask: 0x0259086a

        Port GUID: 0x0008f104039a08dd

        Link layer: InfiniBand

    Port 2:

        State: Down

        Physical state: Polling

        Rate: 10

        Base lid: 0

        LMC: 0

        SM lid: 0

        Capability mask: 0x0259086a

        Port GUID: 0x0008f104039a08de

        Link layer: InfiniBand

 

in opensm log:

 

Jan 06 17:00:28 817185 [F6D5A700] 0x01 -> sm_mad_ctrl_send_err_cb: ERR 3113: MAD completed in error (IB_TIMEOUT): SubnGet(NodeInfo), attr_mod 0x0, TID 0x1cd1

Jan 06 17:00:28 817200 [F6D5A700] 0x01 -> sm_mad_ctrl_send_err_cb: ERR 3120 Timeout while getting attribute 0x11 (NodeInfo); Possible mis-set mkey?

 

many thanks

Re: HCA extended port counters

$
0
0

counters_ext is not upstream and is MOFED only.

Re: Native VLAN configuration for Mellanox switches

$
0
0

See the below commands:

 

[standalone: master] > enable

[standalone: master] # configure terminal

[standalone: master] (config) # vlan 3

[standalone: master]  (config vlan 3)  exit

[standalone: master] (config) # interface ethernet 1/1

[standalone: master] (config interface ethernet 1/1) # switchport mode hybrid

[standalone: master] (config interface ethernet 1/1) # switchport access vlan 3

 

Verify with the following command:

config) # show interface switchport

Interface       Mode         Access vlan        Allowed vlans   

---------------------------------------------------------------------------------

Eth1/1          hybrid       3

 

Marlon

Viewing all 6275 articles
Browse latest View live


<script src="https://jsc.adskeeper.com/r/s/rssing.com.1596347.js" async> </script>