Re: ConnectX®-3 EN vs Ubuntu 13.04
Hi,I have reviewed the supported OS in the EN driver, and Ubuntu is not supported, you can see the full list:Mellanox TechnologiesMellanox OFED supports Ubuntu 12.04, I noticed you're using 13.04, so...
View ArticleRe: ports active but LEDs not lighting up
Hi,Do you know the Firmware version of the switch?How to perform remotely-managed switch firmware query:1.1) Install MFT (Mellanox firmware tools) on a host connected to the same fabric as the remotely...
View ArticleRe: fca_managerd fail and SRP error
Hi Roy,I would first check the status of the Infiniband fabric. Please enter to the host and perform the following commands:1.ibstat2.ibv_devinfo3.sminfo if you could provide that output
View ArticleClik here to view.
Re: Is there any utility to generate log to diagnose RDMA operation?
Hi,There is a User Manual for programming RDMA available on Mellanox website:http://www.mellanox.com/related-docs/prod_software/RDMA_Aware_Programming_user_manual.pdf There are also courses available...
View ArticleRe: Port 1 IB Port 2 Ethernet - ESXI 5.1 (5.5)
Has anyone figured this out, or can anyone from mellanox comment if this is something that is coming back in the next driver release?
View ArticleClik here to view.
Factory Reset Voltaire ISR9024m without console access?
I purchased one of these units from ebay and just got my confirmation from wireeshark that the unit was never reset prior to being sold, is there a way to reset the unit to factory default without...
View ArticleRe: Voltaire ISR 9024 Console Cable
looks like the easiest way to make one is a usb - serial camera cable and then take a screw drive to it, sound like a plan?
View ArticleClik here to view.
Re: Cannot direct ping between two ConnectX-3 cards
I think you have IP addresses on ib ports that are down.Looks like the other ports are up, gpu0-ib0 and gpu1-ib1. Run ibdev2netdev to make sure. If you start opensm on gpu1 you need to specify the GUID...
View ArticleUse RRAS to nat Infiniband connections to Virtual Machines?
Has anyone tried this? I've gotten about halfway there, but i'm stuck on getting communication to / from the infiniband IPoIB fabric. My suspicions are that RRAS is trying to route to the fabric but...
View ArticleMellanox with RHEL 5 & 6 Performance Test
Hello Team Mellanox, 1st of all thank so much & congratulates !! "Singapore Exchange" the fastest trading on earth. I have few question 1. Where do I get Performance test on RHEL 5.x & 6.x test...
View ArticleRe: Upgrading 4036, media full
Hi inbusiness, Thank you for your help in the matter. The U-Boot, do not contain the build_flash command unfortunately. The best I could find there was the tftpboot, however I could not figure out the...
View ArticleRe: Upgrading 4036, media full
hi Rian, Could you be so kind to clarify, where to link these symbolic files? I guess, basically we need to know where the file should go. We only find traces of upgrade files pertaining to firmware...
View ArticleHow to install MLNX_OFED_LINUX on fedora18?
How to install MLNX_OFED_LINUX on fedora18? Driver can support fedora18?
View ArticleRe: ib_srp disconnect on ESXi 5.0 with H:0x5 D:0x0 P:0x0 error
Unfortunately nothing has changed, still got connectivity issues with ib_srp. 2014-01-03T05:57:25.944Z stratus203 vmkwarning: cpu39:9479)WARNING: LinScsi: SCSILinuxQueueCommand:1175:queuecommand failed...
View ArticleRe: Any success with OFED 2.0-3.0.0 on RHEL 6.5/CentOS 6.5?
I've got OFED 2.0-3.0.0 to build against RHEL 6.5 2.6.32-431.1.2.0.1.el6.x86_64 with minor tweaks to the source rpm.However, someone (from Mellanox?) in another thread mentioned an ETA of a couple of...
View ArticleRe: ib_srp disconnect on ESXi 5.0 with H:0x5 D:0x0 P:0x0 error
ESXi host with the queue problems has been in Maintenance Mode for 4h now and after I issue a "esxcli storage core adapter rescan --all" command, this pops out in the vmkernel.log file:...
View ArticleRe: MLNX_OFED_LINUX installtion Error: Error: The current MLNX_OFED_LINUX is...
ibv_devices should show something like this, regardless how the ports are configured device node GUID ------ ---------------- mlx4_0 0002c9030.... Do...
View ArticleClik here to view.
Re: Any success with OFED 2.0-3.0.0 on RHEL 6.5/CentOS 6.5?
2.1 version with RHEL 6.5 support should be available from mellanox.com web site on 1/8 or 1/9
View ArticleRe: Does ConnectX-3 support Amphenol's QSFP+ transceiver?
Hi, If a valid cable or module is connected QSFP, SFP+, or SFP with EEPROM in the cable/module, the connectX-3 will get the cable information from the EEPROM on the transceiver.Did you try another...
View Article