Clik here to view.
SX6018 default firmware
Hello, Where i can find default firmware for SX6018 switch?Both images appears to be corrupt.Stuck on u-boot... 2 images at FF400000 and FF600000 but both with problems.
View ArticlePoor Infiniband Performance MT25418 on ESXi 5.1.0 U2
I am using an HP c7000 enclosure with 4 BL685c G1 blades, and a HP 4x DDR IB Swith Module. The blades are running Vmware ESXi 5.1.0 U2 . I am using the Mellanox ofed stack ( MLNX-OFED-ESX-1.8.1.0 )...
View ArticleRe: HPC-X MPI not supporting threaded MPI programs?
You are correct. The current HPC-X does not build with thread support. However, HPC-X does come with the source and instructions to build, so it can be compiled with the thread support separately if...
View ArticleRe: SX6018 default firmware
Hi Catalin, can you attach a screenshot or the full switch console log?
View ArticleRe: HPC-X MPI not supporting threaded MPI programs?
Thanks, I hadn't done my homework. I thought the tar ball in HPC-X was the regular OpenMPI only, but now that I looked I realize that the yalla driver is included. Thanks for pointing it out. /Nils
View ArticleRe: SX6018 default firmware
Checking Image at f4000000 ...Bad trap at PC: 7ff7e7fc, SR: 29000, vector=1300NIP: 7FF7E7FC XER: 00000000 LR: 7FF6C6A0 REGS: 7fe55c78 TRAP: 1300 DEAR: F4000000MSR: 00029000 EE: 1 PR: 0 FP: 0 ME: 1...
View ArticleRe: SX6018 default firmware
Thanks Catalin, I think we need to replace the switch.Please open an RMA request at: Mellanox Technologies: RMA Request Form
View ArticleWhat cabling would one need to go from ConnectX-2 VPI to XFP 10Gigabit...
I've got a couple of ConnectX-2 and ConnectX VPI cards, and the QSFP to CX4 cables I purchased seem to not understand that the other side is 10Gigabit ethernet. What cabling would I need to make those...
View ArticleClik here to view.
MLNX_OFED driver failed to install at Redhat 6.3
Hi, I have a cluster with two nodes with the name mic01 and mic03, which are installed Redhat 6.3, and mic01 mounted from mic03. I install the MLNX_OFED driver...
View ArticleClik here to view.
LED light indicator on connectX-3 - possibly dead port
Hi, I have just now plugged in a SFP into a new test setup (connectX-3 card) and plugged the other end of the fibre cable into a Cisco switch. Here's what the setup looks like right now by way of the...
View ArticleClik here to view.
Re: Mellanox Messaging Library RPM
Our adapter card is based on the MT23108 InfiniHost device. It appears that the last release to support this was Mellanox OFED 1.5.2-2.1. Unfortunately, the MLNX_OFED Download Center archive only goes...
View ArticleRe: vSphere OFED 1.8.3 Beta
Is there no problem when you make a host profile with iSER?
View ArticleRe: How can I get SX1036 (with L3 and 56g license) work with PPPoE?? I have a...
Any add-ons or other upgrades that add PPPoE support? If not from Mellanox maybe 3th party?
View ArticleRe: Best way to connect/cable WAN/Internet to Mellanox Switch, Advice on...
Thank you for your input! Anyone else up for some of the other questions ? Hope so!
View ArticleClik here to view.
Re: vSphere OFED 1.8.3 Beta
Not able to create host profile with iSER enabled. Error: Unknown.
View ArticleRe: LED light indicator on connectX-3 - possibly dead port
I found in an older connectX-2 pdf this statement. Blinking indicates a problem with the Physical link Which is odd for me as it does this with the SFP plugged in only no cable connected. This is...
View ArticleSX1012 Switch and connect to a Dell PowerConnect 2824
Hi All, I had a look around the forum and looks like one of the question is very close to what I'm think about. I'm looking to add a few Nutanix Nodes to my network, which connect via 10Gbe SFP+,...
View ArticleRe: SX1012 Switch and connect to a Dell PowerConnect 2824
Hi Chris, I think you can use the below: SX1012 - QSA - MC3208411-T - twister pair cable -> 2824 you would need to lower the port speed on the SX1012 to 1000 Mbps and your good to go. The QSA ( QSFP...
View ArticleRe: SX1012 Switch and connect to a Dell PowerConnect 2824
Hi eddie, Thanks for the response, just to clarify, Is The QSA ( QSFP to SFP adapater) PN is MAM1Q00A-QSA Actually the QSFP+ to SFP+ Thanks Chris
View Article